Network Monitoring

Even among the largest state-wide systems, network monitoring practices vary from strict, structured 24/7 internal operations to a reactive approach – responding only to complaints from system users.

Why are relatively few Public Safety systems proactively monitored? Back in the days of software-free radio systems, not much could go wrong. As long as there was power at the sites, power amplifiers did not burn, and antennas were not damaged by lightning, your system was probably in good shape. Should anything go wrong, your subscribers would quickly tell you that their channel was not working. As a result, many people in charge of digital radio systems do not give monitoring a sufficiently high priority.

Dedicated 24/7 resource can be expensive, but your network should be monitored, regardless of size, using the approaches matching your needs and capabilities. Alternative methods to 24/7 Network Operations Centers (NOCs) include:

  • system monitoring terminals at dispatch centers,
  • automatic page or text messages to technical or administrative personnel in case of an alarm,
  • ad hoc monitoring by local service providers (internal or external).

So while you don’t need 24/7 staffing if you have a good alternative system in place, simply maintaining the status quo for the many under-monitored systems is no longer viable. Software-dependent digital networks are subject to glitches, viruses and compatibility issues. They are heavily dependent on correct operation of complex subsystems such as fiber backhaul (often provided by a telco), and are subject to frequent software upgrades. So they are much more vulnerable than analog systems.

As networks become more complex and interconnected, a virus brought into a dispatch console (perhaps doubling as a gaming PC during the slow hours) can cause serious issues for your entire network.

Your P25 network should be monitored regardless of its size, with management methods and resources that match your organization’s needs and capabilities.

Risk factors

At RF sites/equipment rooms:

  • Copper theft,
  • Power loss,
  • Intrusion
  • Antenna system failures
  • Environmental issues
  • Lightning strikes

At dispatch centers:

  • Backhaul failures
  • Fiber – operator errors
  • Microwave – weather
  • Theft and misuse

Subscriber devices:

  • Too many to list!

Maintenance and administrative equipment:

  • Calibration
  • People accessing the terminal and changing parameters haphazardly without reporting it to anyone

Who should monitor your network?

The technical tools for monitoring P25 networks are well known and widely available. Network management applications can monitor system activity and compile useful analyses and reports. These, in turn, can be used to observe trends, identify over (or under) utilized sites and consoles, and anticipate where channels or sites need to be added.
A greater challenge is to obtain technical resource to monitor and interpret network status information.

Large systems

Systems with thousands of users (state-wide networks, large counties or major metropolitan areas) should operate their own 24/7 network operation centers (NOCs). NOC personnel typically monitor network performance and take responsibility for system configuration, user ID creation and talk group management.

Mid-size systems

Where dedicated 24/7 NOCs are not feasible, you can look for a shared one, using a mix of vendors, local service shops, and large systems nearby.

A shared NOC can monitor system performance metrics, provide alerts, deliver performance reports. In the event of an alarm, often a vendor may not even need to involve you to rectify the issue. A disadvantage is that you may be competing for a shared NOC’s attention with other systems, and a vendor is likely to be monitoring remotely via the internet, which is of less use in a disaster.

A multi-layered approach with a manufacturer or vendor, service provider and internal techs means lots of eyes watching your system from multiple perspectives – your in-house experts during the day, and a contracted local vendor or a friendly NOC at night.

Small systems

If you choose to monitor your system yourself, remember that the tools provided and expectations placed on your maintenance team are critical to success.

Active monitoring allows you to respond proactively, and not to simply rely on your users’ complaints. Where this is feasible you should set up alarms to trigger paging or SMS to technicians on duty. If you involve your PSAP, educate your field staff and dispatch well. For example, when a call is dropped, users must report formally which radio and location, so you can keep track of events. Make this process a part of your standard operating procedures.

Monitoring by dispatch

Some agencies opt for dispatch personnel to monitor their networks. This is controversial for two reasons:

  1. This additional task can potentially conflict with dispatchers’ primary life-saving and property-saving responsibilities.
  2. System monitoring and issue reporting requires technical knowledge beyond the understanding of most dispatchers.

Ideally you would not burden your dispatch personnel with monitoring, but it may be a matter of necessity, typically due to financial constraints. On the positive side, properly set-up alarm systems may be embraced by dispatch personnel.

If you must use your dispatch personnel for self-monitoring:

  • provide appropriate training, including scheduled refresher sessions,
  • provide clear instructions and SOPs,
  • strive for a balance, making sure monitoring receives sufficient attention without interfering with the primary objectives of the dispatchers,
  • bring all alarms, clearly labelled, to one terminal so that the monitoring personnel can easily interpret them and commence the appropriate course of action.

No Public Safety communication system should rely on complaints from users as its principal monitoring method.

However, officers in the field will provide invaluable radio performance information, for better diagnosis of issues like dead spots and interference.

Use the "NEXT" button to keep reading through the "Managing" P25 Guide, or select a topic from the menu below.

Managing your P25 System: Articles

2 responses to “Network Monitoring”

  1. vik says:

    May I please know what the tools for monitoring P25 radios and networks?

    • Hello vik,

      Thank you for your enquiry.

      For P25 networks, we have Enable Monitor to track the condition of a P25 network. Visit this link for more information and a short video on it: http://www.taitradio.com/products/tait-enable-network-management/enablemonitor

      At an individual repeater level, we can also use Enable Monitor, however there are extremely comprehensive remote diagnostics and monitoring inbuilt to the Tait TB9400 or Tait TB9100 repeaters which would be used.These are accessed through the included web user interface with these products.

      Services from Tait are likely to be required to individually configure Enable Monitor for your particular operation.
      In the future we will Introduce Enable Report (information also included) for operation on P25 networks.

      If you wish for further information, it would be helpful to know your name, organisation, and location, so that we can correctly direct your enquiry further within Tait.

      Thank you again for your enquiry.

Leave a Reply to vik Cancel reply

Your email address will not be published. Required fields are marked *